Adler class 743-221 Manuel d'instructions

743 - 221Sewing unit for the automated sewingsingle-point darts with straightor curved seam formand for the sewing of pleats.Instructions for operatin

2.3 DisplayThe Microcontrol controls are equipped with a 2 x 16 digit display.It displays program number, sewing lengths, underthread reserve andpiec

3. Description of the Function Keys3.1 Selecting and Adjusting the Seam LengthThree stored seam lengths can be selected via the L1, L2 and L3keys. A

3.4 Setting Parameter ValuesThe set parameter values / seam lengthsare changed via the " + " or " - " key.–Press the " + &q

3.8 Securing at the Seam EndEnd securing at the seam end is selected by pressing this key.The end securing is only conducted if it is activated with

4. Setting the Sewing and Testing ProgramsThe sewing and testing programs are selected with the " Program "selection switch.–Set the "

4.2 Sewing Program for DartsThe program positions 10 ...29 are available for free programming ofdarts and pleats.The programming mode is activated by

–Press the " Σ " key.Set the number of stitches for stitch condensation at the seambeginning.Setting range: 3 - 8 stitches Resolution: 1

4.4 Setting the Underthread CounterThe underthread counter is set in program 41.The presetable decrementer monitors the underthread reserve.The decre

4.6 Stopping Point for the Function SequenceA sewing program with stopping points is run through in program 43.–Set the " Program " switch

4.8 Test of the Step Motor Drive PulseProgram 57 checks the step motor controller and the outputs of thestep motor.–Set the " Program " swi

Anleitung, komplettManual, complete743 - 221Postfach 17 03 51, D-33703 Bielefeld • Potsdamer Straße 190, D-33719 BielefeldTelefon: + 49 (0) 5 21 / 9

4.10 Continuity TestProgram 60 checks if the 24 V current supply supplies current with theoutput drivers turned off.Then program 60 checks all existi

Key Function Symbol Displayb814 Stitch condensation NA LEDb815 Setting the counter Displayb816 - Reserve -b817 - Reserve -b818 Blower from above / blo

4.12 Checking the Input ElementsProgram 62 checks the input elements.–Set the "Program" switch to "62".–Press the "STOP"

4.14 Selecting Output ElementsCaution Risk of Injury !During the function test do not reach into the running machine.Choose your position so that no

4.16 Positioning the Machine Head in the 1st Needle PositionProgram 67 positions the machine head in the 1st position (needledown).–Set the " Pr

6. Step Motor OutputCaution Electric Current !Turn the main switch off !The switches may not be adjusted while under current.The switches must be in

ForewordThis instruction manual is intended to help the user to become familiarwith the machine and take advantage of its application possibilities in

General safety instructionsThe non-observance of the following safety instructions can cause bodily injuries or damages to the machine.1. The machine

Contents Page:Part 4: Instructions for programming DA Microcontrol Cl. 743-221 . Program version: 743221A31. General . . . . . . . . . .

1. GeneralThe MICROCONTROL controls of the DÜRKOPP ADLER 743-221include the integrated comprehensive MULTITEST testing andmonitoring system.A microco

2. Description of the Controls2.1 Operator Controls on the Front PanelKey Function Key FunctionSelecting sewing and testing programsSeam length L1Se

2.2 Operator Controls at the ControlsThe needle- and underthread monitors are activated with the DIPswitch b417 at the controls.The dials b401 and b4